AhlsellProductsVentilation

Ventilation

Make sure you have good ventilation products! Ahlsell's ventilation range spans duct systems, devices, valves, indoor grills, hoses with accessories, roof hoods, exterior wall grills, ventilation accessories, filters, mounting materials, fans, aggregates, cooker hoods, controls, regulations, fire gas dampers, and flat strip plates.

Products (1042)
Fresh Air Vent Fresh TL100DE T NEW
Fresh
Fresh Air Vent Fresh TL100DE T NEW
Art. no.: 9302642
Fresh fresh air vents are installed in bedrooms and living rooms. A rule of thumb for the correct number of vents is one in each bedroom and two in the living room. In some cases, it is wise to increase the number of vents if multiple people sleep in the same room or if the total living area is larger than usual. The Fresh TL DE series are sleek wall vents. TL DE comes standard with condensation protection, storm protection, and is also paintable. The vent has a telescopic function of 185-340mm; for thicker walls, extend with modular pipes. Installation/Placement The vent is placed high up on the wall, approximately 220 cm from the floor or with the top edge of the vent at least 10 cm from the ceiling.

The vent is excellent for use with underfloor heating. In this case, place the vent at least one meter from the window to prevent cold drafts due to cold radiation through the window. The vent should be placed directly above the heating element. This utilizes the rising heat from the radiator, known as convection current. Comfortable air distribution The air distribution is carefully developed; the vent releases air upwards and to the sides.

The outside air mixes very effectively with the room air, and just a few decimeters from the vent, the incoming air has reached a comfortable temperature. Storm protection saves energy Regardless of the weather, the storm protection slows down high airflows, which contributes to lower heating costs compared to a traditional vent. The storm protection provides good comfort in the room and reduces the risk of drafts.

Filter and maintenance Maintain good indoor air quality by regularly changing and maintaining your filters. To ensure good air quality and maintain flow, the filter should be cleaned or replaced one to two times per year. The standard filter is washable; use a mild soap solution. The pollen filter and electrostatic filter should be replaced with new ones. The filter is mounted in a filter holder behind the front. The front can be easily folded up for access to the filter holder. When using the electrostatic filter, the filter holder is replaced and cannot be combined with storm protection.
Replaces 9302600 (629700)
Fresh Air Vent Fresh TL100DE T NEW
Heat Recovery Unit EvoAir A30T EPP EvoControl MPO G3 White, Acetec
Acetec
Heat Recovery Unit EvoAir A30T EPP EvoControl MPO G3 White, Acetec
Art. no.: 66110099
Ventilation unit EvoAir A70T EPP EvoControl White is suitable for installation in kitchens or for example laundry in homes up to 120m².
• Rotary changers • EC motors • User-friendly control • Easy assembly, reversible in right / left version • Lowest construction height of 53.5cm simplifies duct traction • Low weight, 23kg • Supplied with double belt drive as standard. Sleeve dimensions on the connections.

EvoControl
• 4.3 inch color panel with touch display. • Wired network connection. • Cloud solution with responsive design that adapts to mobile, tablet or computer.

Features
• Control via the cloud • Timer • Pressure control • Air quality control • Humidity control • Logging of measurement values and history • Clear text and parameters • Flow chart
Hygrostat RH15 för MG90, Munters
Munters
Hygrostat RH15 för MG90, Munters
Art. no.: 19063224
HMH2 is a 2-step electromechanical hygrostat for controlling and regulating humidification and/or dehumidification systems in climate and ventilation installations. HMH2 has two micro switches. The step difference between them can be adjusted steplessly with a set screw. The hygrostat uses a hair element as a moisture sensor. Since the contacts are changeover, the hygrostat can control both humidification and dehumidification. Comes in standard design with changeover contact 250V AC 10A. Since the contacts are changeover, the hygrostat can control both humidification and dehumidification. Can be mounted in a duct or on a wall. The hygrostat is delivered with a bracket that fits both mounting methods. Setting range 10-100% RH with a switching differential of 3% RH at 45% RH. The temperature range refers to the maximum allowable temperature at the sensing element, ambient temperature at the device housing. The dimensions refer to the device housing. The tube has a length of 222 mm with a diameter of 35 mm.
Wall fans KVFU, Östberg
Östberg
Wall fans KVFU, Östberg
Art. no.: 6611165
Wall fan with circular inlet and square mounting plate. Is compact with high capacity and efficiency. The fan wheel is equipped with backward-curved blades. The outer rotor motor has maintenance-free double-encapsulated ball bearings. Comes with integrated motor protection and junction box with protection class IP 54. For speed control, a transformer or thyristor can be connected. The fan housing is made of galvanized sheet steel. The fan is intended for installation in duct systems, mounted on the inner wall. Easy installation in any position and can also be used in humid environments. Maximum temperature of transported air is 60 ° C for all models with some exceptions. Models 315B / C ErP have a maximum temperature of 50 ° C, 160C at 65 ° C and model 125C a maximum of 70 ° C. Insulation class, motor: F.
Wall fans KVFU, Östberg
Systemair
Wall fans KVFU, Östberg
Art. no.: 6611100
The KV sileo series is intended for installation in ducts. All KV fans have a connection socket at least 25 mm long. Mounting brackets FK make installation / disassembly easy and prevent vibration transmission to ducts. The fans have backward-curved blades and a maintenance-free outer rotor motor. The KV sileo fans can be voltage regulated with a stepless thyristor or 5-stage transformer. To protect the motor from overheating, the fan has a built-in thermal contact with manual reset. The housing is made of galvanized sheet steel and is folded, which gives an almost airtight housing. If the fan is ducted, it can be installed outdoors and in wet rooms. This is possible thanks to the tight housing of the fan.
• High efficiency • Voltage adjustable • Built-in thermal contact • Can be mounted in any position • Can be installed outdoors • Maintenance-free and reliable
Supply Air Diffuser EAGLE Ceiling CC, Swegon
Swegon
Supply Air Diffuser EAGLE Ceiling CC, Swegon
Art. no.: 19057825
Square Air Diffuser EAGLE Ceiling CC (Ceiling Circular).
Consists of a plenum box and a front panel, the front panel is equipped with aerodynamically designed adjustable nozzles in a circular nozzle pattern. The front panel is hinged on one side and fastened with springs on the opposite side. This mounting, Quick Access, allows for easier and faster handling during installation, adjustment, and cleaning. The air diffuser is also available in a low-profile design when low building height is required and is then delivered without a spigot (not size 400-600). The plenum box and front panel are made of sheet steel. The connection spigot is made of galvanized sheet steel. The air diffuser is painted inside and out in a standard white color, RAL 9003/NCS S 0500-N. The nozzles are made of plastic (PP-Polypropylene). The diffuser is suitable for installation in cassette ceilings but can also be advantageously installed in fixed ceilings. The nozzle technology allows for air supply with a large temperature difference. The diffuser is suitable for both constant and variable air flow.

The maximum air volume is specified at 30 dBA, 50 Pa, and including the connection box. The design refers to the number of nozzles.
Mount in connection box type ALSd which is ordered separately.








Showing 52 of 1042