Versatile luminaire for industries, basements, garages or other equivalent indoor environments that require IP44. Frame of white-lacquered aluzinc, ends of impact-resistant plastic and dome of opal linear prismatic acrylic. The sensor luminaires have a built-in HF motion sensor and twilight relay for max. 400VA LED load. The sensor fixtures can be connected in groups with one or more sensor fixtures as master and 6 slave fixtures. Always take the sensor's maximum load into account and use contactors if necessary. Sensors with HF technology can in some cases detect movement on the other side of thinner walls. Flexible installation on a dense ceiling, on a wall bracket, luminaire rail or rope. Attachment c-c 900 and 1200 mm respectively. Connection through 13 mm knockouts in the ends and on the top of the luminaire (minimum size only in the ends). 5-pin quick connection terminal block with the possibility of further connection mounted in the middle of the luminaire.

Ceiling luminaires with a modern design language for indoor installation. Available in two sizes where the smaller can be set in three power steps 24W-18W-10W (2400lm-1800lm-1000lm) and the larger in two steps 38W-29W (3800lm-2900lm). Both sizes can be adjusted between 3000K and 4000K. All adjustment takes place with dip switches on the luminaire before assembly. The smaller luminaire is available as on/off and with HF sensor and background light. The sensor fixture cannot be used to control additional fixtures. The sensor fixture does not work optimally in rooms with irregular ceiling height and is therefore not recommended for e.g. stairwells. The larger fixture is available as an on/off and Dali/PushDim version. Both sizes can be mounted directly to the ceiling, the smaller one can also be mounted over a ceiling box.

Dimmable actuator for 350mA loads. The load is connected in series on the secondary side. Light control is done on the primary side.

230 V LED strip in IP44 design for durable and practical lighting on the construction site. Can be used both indoors and outdoors. High luminous flux and good color reproduction. Length 25 meters. Luminous flux 800lm / meter. Supplied without connection cable (7590125). Can be spliced up to 100 meters with a connection cable.

Floodlight intended for general indoor and outdoor lighting, for example loading docks, garage driveways and buildings. Unique design with a slim luminaire housing. Strong rust protection thanks to aluminum luminaire housing and bracket with stainless screws. Well suited for outdoor use. D-marked. Tempered front glass with UV-resistant silicone rubber gasket. Symmetrical luminaires up to 48W also suitable as work lighting for mounting on stands 7570106. Pre-assembled suspension bracket in aluminum for mounting on wall, ceiling or stand. The bracket can be removed if necessary to facilitate mounting. Connects with pre-assembled cable and supplied plug (symmetrical) or pre-assembled connection cable (asymmetrical).
Ambient temperature Celsius: Symmetrical: -30° to +50°. Asymmetric: -40° to +50°

LED actuator (combined LED actuator and LED dimmer) for constant current 350, 500 or 550 mA up to 8W. Equipped with dip switches for selection of outgoing current. Dimmed using spring-back pushbutton or 1-10V control unit. Up to 20 units can be dimmed with 1 pushbutton.

Luminaires for garages, wet rooms or other equivalent indoor environments that require IP66 and functional lighting. D-marked. Not suitable for installation in laundries, animal stables or other environments with aggressive chemicals. Frame and cup in polycarbonate with clips in stainless steel. Can be mounted close to the ceiling / wall, suspended or on a rope. Mounting bracket in stainless steel and bracket for rope mounting included. Mounting CC 770 mm. The cover can be locked with the included safety screw. Connection: Cable entry through PG 13.5 knockouts in the ends. Cable glands included. Prepared for connection in the ends with terminal block 5G2.5 mm. Luminaires with industrial devices have drive devices equipped with 4kV overvoltage protection and can withstand higher ambient temperatures.

Indy 23 is a luminaire for dry and dust-free environments in warehouses, manufacturing and trade. Adjustable luminous flux (7218780 = 5500/7000 lm, 7218781 = 9000/11700 lm) or Dali control provides flexibility for different businesses and needs. Mounted close to the ceiling/lighting rail or on a rope with the integrated mounting bracket. Lenses for medium wide light image provide minimal stray light and glare. The luminaire's low weight provides good ergonomics during assembly. Connection and adjustment of light flux takes place at the ends of the luminaire behind a cover with a snap lock.

230 V LED strip in IP44 design for durable and practical lighting on the construction site. Can be used both indoors and outdoors. High luminous flux and good color rendering. Available in 5m, 10m, 25m and 50m rolls with pre-assembled cord stand (80cm), earthed plug for easy installation. Luminous flux 800lm / meter.

Emergency light luminaire for led light and reference in public premises such as hotels, offices, schools, shops etc. Flexible single-sided luminaire for indoor use with high encapsulation class (IP65). The luminaire is switchable for permanent or contingency operation, equipped with energy-efficient LED light source, autotest from NiMH battery. Pictogram set with 22 meters. reading distance is included. Surface-mounted on the wall or ceiling with or without pictogram foil.

Field of use
Over workbenches, in kitchens, washrooms, kitchenette
Performance
Frame of white powder coated steel sheet. Fittings in white ASA plastic. 10 / 16A double grounded pet-proof socket and flip switch on the underside of the luminaire. Low build height and easy assembly. Supplied with pre-assembled LED fluorescent lamp 3000K with 35'000 hours. The light source is interchangeable.
Mounting
Mounted on the underside of cabinet or shelf. Reversible cover for positioning the sockets optionally to the right or left.
Connection
Conduction through 13 mm knockout in each end and long sides. Connection via quick connection terminal max. 2.5 mm². "

Spare shades intended for indy44 T5 industrial light fittings.

Low-rise downlight with drive unit for recessing in normal ceilings with plaster and sparse panel. No need for safety box. Heatsink, protective cover and ring in aluminum for optimal heat dissipation. Angled inner part with reflector and partially frosted glass for minimized glare. Supplied with dimmable 350mA driver and quick-connect terminal block for 230V, divisible between driver and luminaire. Downlight power without drive 5.4W. Does not need to be fitted with a safety box.

Suspended office luminaire designed for the highest possible efficiency and light comfort. Well-recessed light points minimize glare. Light distribution 60% down and 40% up. Spreading angle 80 ° downwards and 120 ° upwards. Drawstring for ignition and light control. Comes with wire suspension and cord stand.

Downlight for general lighting in homes and spaces with normal ceiling height in public premises. Made of aluminum for optimal heat dissipation. Angled bar. To be fitted with a safety nest. Delivered in a package of six luminaires complete with drives.

Applications:
Downlight with very good color reproduction which is excellent for general lighting.
Design:
Supplied with dimmable actuator and extra reflector for desired spreading angle.
aLED 8 comes with three reflectors (24 °, 36 ° and 64 °).
aLED 11 comes with two reflectors (24 ° and 36 °).
Mounting
Recessed ceiling, plaster, panel or similar. Installed with safety box.
aLED 8 Hole cutting 73 mm and recess depth 35 mm.
aLED 11 Hole cutting 79 mm and recess depth 67 mm.
Connection
Dimmable driver connected to 230V with quick-connect terminal and strain relief for cable or flex pipe. Double connections per conductor.
AmbiDim 2200-3000K

Robust and bright work lamp that can be mounted on a stand, placed on the floor or hung on the wall. The luminous flux can be adjusted to 50% or 100%. Two sockets on the back. 5 meter connection cable.

Area of application:
General surfaces, garage or other similar indoor environments requiring IP44 a functional general lighting system.
Version:
D-marked, encased, all-purpose LED fixture, IP 44. Slim white-lacquered body. Aluzinc, with durable plastic ends. Diffuser, acrylic opal-line prismatic. Available in Light colour 830 and 840.. With or without a sensor. The sensor fixtures have built-in
HF motion sensors for max 500VA LED load. Sensor fixtures can be connected in groups with one or more sensor fixtures as a master and 6 pieces of slave fixtures.

The DALI CF luminaires come with one combo for DALI, SwitchDIM and corridor function (CF). The luminaires have corridor function (CF) with basic light (30 minutes after-light at 10% fog level), available as master with sensor (DALI CF Sensor) or slave without sensor (DALI CF). A maximum of 20 slaves (DALI CF) can be connected, including masts. Can also be delivered with on-demand and other configurations of DALI CF (on call time and fog level) on request.
Assembly:
Flexible mounting direct to the ceiling, on a wall bracket, fixture rail or line. Attachment c-c 520, 900, and 1200mm respectively.
Connection:
25 W: Cable insertion through 13 mm knockouts in the ends.
Others: Cable insertion through 13 mm knockouts in the ends and on the top of the luminaire. 5-pole quick-connect terminal with the possibility of diverting mounted in the middle of the luminaire.
Luminaires type ÖK have five-pole quick-connect terminals at each end for easy switching. Installation instructions for the sensor are available at www.ahlsell.se "

Robust luminaire for facade and balcony. Uplights and downlights can be screened from a broad beam to a narrow line. Equipped with two sockets with lids. Quick terminal with the possibility of forwarding.

Suspended luminaire with up and down light for lighting, for example, desks or other work surfaces in an office environment. Frame of white lacquered aluzinc with end caps in ASAplast. Silver-grey cross-slat louvre protection with diffusing disc. Two pull cords for separate lighting/dimming of up- and downlight. Mounted suspended in the included wire pendant with friction lock, preferably in a luminaire rail or ceiling profile to facilitate adjustment afterwards. Attachment c-c 1200 mm. Mounted cord rack with earthed plug 2.2 m.

Downlight intended for recessing in cover plate under cupboard in kitchen. Wide spreading angle provides even working light. Easy to install with connection terminals for + and - and two terminals for splicing the negative conductor back to the drive.

Luminaire for installation under cupboards in kitchens and the like. Frame in lacquered sheet steel with linear light emission. Well-dimmed and even wide light image.

Work lamp with rotatable lighting. Can be placed on the floor or hung on the wall or in a hook. Available in mains-powered and rechargeable version.

Versatile luminaire for industries, basements, garages or other equivalent indoor environments that require IP44. Frame of white-lacquered aluzinc, ends of impact-resistant plastic and dome of opal linear prismatic acrylic. Connection through 13 mm knockouts in the ends. Five-pole quick-connect terminal block at each end for easy switching.

Post luminaire with indirect light intended for park roads, courtyards and similar public areas adjacent to residential buildings and offices. Robust luminaire in powder-coated cast aluminum and cup in clear polycarbonate. LED module mounted in the lower edge of the hive with a reflector in the upper part provides a naturally even and glare-free light. Mounted on post with top diameter Ø 60 mm. Recommended post height 3-4 meters. The luminaire is delivered with pre-assembled 6m H07RN-F 3G1.5 cable.

Area of application:
General lighting in offices and similar environments with suspended ceiling systems
or in hard ceiling with kit for surface mounted assemblies.
Version:
Recessed LED fitting for false ceiling with actuator.
White lacquered frame in aluminium. With or without DALI.
Available in colour temperature 3000K and 4000K. Opalised cover to
create a pleasant light distribution and minimise glare. IP class 40.
Assembly:
Fits into sub ceiling’s T- profile.
Connection:
Non-dimmable versions (7013474 and 7013475) are connected with pre-assembled cable stand 2.2 m.
Dimmable versions (7013476 and 7013477) are connected with 230V in the actuator.

High-height luminaire for open spaces. Varnished in Akzo Nobel powder coating in a light gray shade that is suitable for both industrial environments and shopping centers. Mounted pendulum in chain or wire. Spreading angle 110 °.

Small, flexible and bright battery-powered work lamp. Charges with USB and also works as a power bank. Built-in footrest, magnetic attachment and hook for hanging. The light flux can be set in three positions and flashing. Light time 2 hours at 100%. Charging time 3 hours.

White indoor wall lamp with two, side- mounted LED modules.
Suitable for hallways, stairways, and similar locations.
Discreet design with lacquered, white, steel frame, arched opal acrylic shade provides excellent glare control. Easy and quick installation.
Assembly:
Mounted in wall with two screws. The shade is folded in place and fixed with a screw.
Cable feed entry from above, bottom, or back.
Accessories:
Mounting plate is available as an accessory.
Mounted behind the fixture to smooth the surface and conceal screw holes from previous installations.
Screws for mounting the fixture and mounting plate are included.

Universal LED actuator (combined LED ballast and LED dimmer) for up to 30W per channel. Can drive both constant-voltage and constant-current diodes. Equipped with DIP switches for selection of output voltage/current. Extensible on the primary side. Dimmed using spring-back pushbutton or 1-10V control unit. Up to 20 units can be dimmed with a push button; no extra synchronisation cable is required. Both of the two-channel actuator’s channels can be dimmed with a single push button.

Park fixture in an elegant design with two different light patterns adapted to open spaces and GC roads. Cast aluminum frame with polycarbonate (PC) dome. Painted in gray (RAL9007) which also fits well on a galvanized steel post. The luminaire is available with two optics intended for lighting large areas (symmetrical) or walkways and the like (asymmetrical), and in two color temperatures (3000K and 4000K). Mounted on a pole with a diameter of 40-60mm. Suitable mounting height 3-4 meters. Supplied with 5 meter rubber cable.

Drives intended for aLine LED strip but also other 24V LED strips.

Bollard luminaire with indirect light intended for park roads, courtyards and similar public areas adjacent to residential buildings and offices. Robust luminaire in powder-coated cast aluminum and cup in clear polycarbonate. LED module mounted in the lower edge of the hive with a reflector in the upper part provides a naturally even and glare-free light. Mounted on foundation with insert diameter Ø mm.

Area of application:
Compact LED spotlight kit for offices, home environments, restaurants, hotels and similar premises.
Low heat generation and long service life compared with halogen lamps.
Version:
Consists of 3 8W LED COB Spotlights and 1 m single-phase track, connector, longitudinal connector and end cap.
Body in cast white-painted aluminium with plastic lens and plastic adapter.
The light sources are not replaceable. Recommended dimmers: Rotary dimmer
1360113 (Schneider), 1363147 (Elko) and 1377482 (Vadsbo).
Box dimmer 1377440 (Vadsbo) and 1377065 (Eltako).
Assembly:
Flush to ceiling, two attachment points (hole 10x5 mm).
Connection:
Connected with 230V.
The track must have protective earthing.

Lamp holder, fully threaded jacket.

Flexible and powerful LED work lamp for indoor and outdoor use. Practical handle and shoulder strap that makes the luminaire easy to carry. Housing in impact-resistant polycarbonate. Available for mains connection and battery operation. Can be placed on the floor, hung on a wall or mounted on a stand.

Version aWork LED Tec 3600:
Power switch on / off and adjustable between 50% / 100% brightness on the back. Also has two anti-slip 230V sockets on the back. Comes with pre-assembled cord stand 3m H07RN-F 3G1.5mm and plug.

Version aWork LED Tec 2400 Battery:
Rechargeable work lamp LED. Power switch on / off and adjustable 50% / 100% brightness on the back. Lithium battery 11.1V / 4400mAH. Comes with charger for 230V and 12V. Battery time 2.5-4.5 h. Charging time 7-8 h.

Version aWork LED Tec 4800:
Power switch on / off and adjustable between 50% / 100% brightness on the back. Also has two anti-slip 230V sockets on the back. Comes with pre-assembled cord stand 3m H07RN-F 3G1.5mm and plug.

Floodlight with PIR motion sensor in a compact design for general indoor and outdoor lighting. Black powder-coated aluminum frame with tempered front glass. Supplied with 3 m cable and plug. Suspension bracket in aluminum for mounting on a wall, ceiling or stand. For fixed installation, the cable is cut to the appropriate length and connected in a junction box. The motion detector has a detection angle of 120°, range of 2-8 m which is adjustable, delay of 10 sec-8 min, twilight relay 2-2000 lux. Recommended installation height is 1-3 m.

Indicating luminaire for showing escape routes in case of power failure in public premises such as hotels, offices, schools, shops etc. Intended for permanent operation. Frame in aluminium with plate of plexiglass hanging underneath for single or double-sided reference. The luminaire is equipped with energy-efficient LED light source and autotest with built-in NiMH battery. Comes with 3 pictogrammes, read distance: 25 m. Mounted surface-mounted against a wall or ceiling indoors. Mains voltage is connected in the terminal box with the plug-in version. 1 year warranty on battery.

Pictogram set for aMergency Light. With three different pictograms.

Floodlights in a compact design for effect lighting indoors and outdoors. The color shade is set with the supplied remote control. Black powder-coated aluminum frame with tempered front glass. Supplied with 3 m cable and plug. Suspension bracket in aluminum for mounting on a wall, ceiling or tripod. For fixed installation, the cable is cut to the appropriate length and connected in a junction box.

Low-rise downlight with drive unit for recessing in normal ceilings with plaster and sparse panel. No need for safety box. Heatsink, protective cover and ring in aluminum for optimal heat dissipation. Angled inner part with reflector and partially frosted glass for minimized glare. Changes color temperature in connection with dimming from 2100K - 3000K. Supplied with dimmable 350mA driver and quick-connect terminal block for 230V, divisible between driver and luminaire.

LED Reflector lamp

Spotlight for lighting in shops and exhibitions. Mounted in three-phase rail. Interchangeable reflector 24 ° or 36 °.

Headlights in compact design for general indoor and outdoor lighting. Black powder-coated aluminum frame with tempered front glass. Comes with 3 m cable and plug. Aluminum suspension bracket for mounting on a wall, ceiling or stand. For fixed installation, the cable is cut to the appropriate length and connected in a junction box.

Spare light covers for industrial fittings E7298420 and E7298421 Indy66.

Minidownlight intended for recessing in window niches and furniture. Supplied with spreading angle 20 °, lens for 40 ° included. Easy to install with connection terminals for + and - and two terminals for splicing the negative conductor back to the drive.

Lamp holder with earth screw.

Area of use
Postage fittings intended for park roads, farms, parking lots and similar public areas adjacent to residential buildings and offices.
Performance
Robust luminaire in powder-coated cast aluminum and clear polycarbonate cover. LED modules with lenses for even light and reduced glare.
Mounting
Mounted on pole with top diameter Ø 60 mm. Recommended chair height 4-5 meters.
Connection
The luminaire comes with pre-assembled 6m H07RN-F 3G1.5 cable. "

Light bulb garage luminaire. The luminaire has a plastic frame, a structural glass cover and an aluminum reflector. Cable insert with choke nipple in one end. With galvanized steel wire mesh, which opens without tools. Grids of steel wire with plastic base. Approved outdoors. 230V. IP44.

Completely assembled with light peg and light holder for temporary lighting of workplaces.

Light holder made of thermoplastic T220º, assembled with a 0.5 m RKUB low-voltage cable.